Oct 31, 2023

What is an accumulator?

Leave a message

What is an accumulator?
1. What is an accumulator?
A hydraulic accumulator is a device that stores energy. In an accumulator, the stored energy is stored in the form of a compressed gas, compressed spring, or lifted load and exerts a force on a relatively incompressible fluid.
Accumulators are very useful in fluid power systems. They are used to store energy and eliminate pulses. They can be used in hydraulic systems to reduce the size of fluid pumps by replenishing pump fluid. This is done by storing energy in the pump during low demand phases. They can act as reducers and absorbers of fluctuations and impulses. They cushion blows and reduce vibrations caused by sudden starts or stops of power cylinders in the hydraulic circuit. Accumulators can be used to stabilize pressure changes in hydraulic systems when the liquid is affected by temperature rise and fall. They can dispense fluids such as grease and oil under pressure.

The most commonly used accumulator at present is the pneumatic-hydraulic type. The gas acts like a buffer spring, working with the fluid; the gas is separated by a piston, thin diaphragm, or bladder.

2. Working principle of accumulator

Under the action of pressure, the volume change of the liquid (at constant temperature) is very small, so if there is no power source (that is, the replenishment of high-pressure liquid), the pressure of the liquid will drop rapidly.

Gases are much more elastic because they are compressible and can maintain higher pressures despite large changes in volume. Therefore, when the accumulator replenishes the hydraulic oil in the hydraulic system, the high-pressure gas can continue to maintain the pressure of the hydraulic oil even if the liquid volume changes. It becomes smaller, causing the hydraulic oil to lose pressure quickly.

As for nitrogen, the main reason is that nitrogen is stable and does not have oxidizing or reducing properties. This is very beneficial for maintaining the performance of the hydraulic oil and will not cause oxidation/reduction denaturation of the hydraulic oil!

Nitrogen is a precharge pressure, installed in the accumulator bladder and separated from the hydraulic oil! When the accumulator is filled with hydraulic oil, due to the pressure of the nitrogen bladder on the hydraulic oil, that is, the pressure of the hydraulic oil is equal to the nitrogen pressure. As hydraulic oil pours in, the nitrogen bladder is compressed and the nitrogen pressure increases. The oil pressure continues to increase until the hydraulic oil reaches the set pressure!

The function of the accumulator is to provide hydraulic oil with a certain pressure, which is generated by the power of nitrogen!

3. Main functions of accumulator

1. Used for auxiliary power supply
The actuators of some hydraulic systems act intermittently, and the total working time is very short. Although the actuators of some hydraulic systems do not act intermittently, their speed changes greatly within a working cycle (or within a stroke). After the accumulator is installed in this system, a smaller power pump can be used to reduce the power of the main drive, making the entire hydraulic system small, light, and cheap.

Hydraulic butterfly valve

2. As emergency power supply
For some systems, when the pump fails or there is a power outage (the oil supply to the actuator is suddenly interrupted), the actuator should continue to complete the necessary actions. For example, the piston rod of a hydraulic cylinder must be retracted into the cylinder for safety reasons. In this case, a battery with appropriate capacity is required as an emergency power source.

3. Supplement the leakage and keep the pressure constant
For systems where the actuator is not working for a long time but the pressure needs to be kept constant, an accumulator can be used to compensate for leakage and keep the pressure constant.

4. Absorb hydraulic shock
Due to the sudden change in the direction of the reversing valve, the sudden stop of the hydraulic pump, the sudden stop of the actuator movement, and even the artificial need for emergency braking of the actuator, etc. , the liquid flow rate in the pipeline will change drastically, resulting in impact pressure (oil hammer). Although there is a safety valve in the system, short-term pressure fluctuations and shocks will inevitably occur. This impact pressure often causes the failure or even damage of instruments, components, and sealing devices in the system, or the rupture of pipelines. It also causes significant vibration in the system. If an accumulator is installed before the source of impact on a control valve or hydraulic cylinder, the impact can be absorbed and mitigated.

5. Absorb pulsation and reduce noise
The pulsating flow of the pump will cause pressure pulsation, causing uneven movement speed of the actuator, causing vibration and noise. A sensitive, small inertia accumulator is connected in parallel at the pump outlet to absorb flow and pressure pulsations and reduce noise.

Send Inquiry