Hangguo:Your Professional Gas Silencer Manufacturer!
 

Hangzhou Hangguo General Equipment Co., Ltd. has been established since December, 2000. As a subsidiary of XIZI Clean Energy Equipment Manufacturing Co,.tld.(Stock code:002534)the Company specializes in the design and manufacture of auxiliary engine and heavy duty equipment for boilers. The company has produced 115 sets of flue gas bypass systems and 159 sets of flue gas baffle doors, covering all continents in the world.

 

 

Gas Silencer Pillar Page Preview

Gas Silencer Manufacturer in China | Parallel Plate Exhaust Gas Silencers for Gas Turbine Bypass Systems

Hangguo is a gas silencer manufacturer and factory in Hangzhou, China, a subsidiary of XIZI Clean Energy (stock code 002534). Every bypass stack we ship for simple-cycle or switching duty can carry our parallel plate-form gas silencer — designed in house against the same 20 years of turbine exhaust experience behind our 126 delivered bypass systems.

A gas silencer lets the exhaust flow pass while it absorbs the dynamic noise of gas venting straight to atmosphere. Ours is engineered as part of the flue, not bolted on as an afterthought: the casing carries its own insulation, the blades are built for gas temperature, and the interface to the diverter damper and the bypass steel structure is detailed by the same team.

Large rectangular gas silencer casing moving out of the Hangguo assembly hall on a multi-axle trailer

Large silencer casing leaving the assembly hall.

126
bypass systems delivered since 2000
48
for 9F-class and larger turbines
20+
years designing gas turbine exhaust
14+
turbine models covered, 6B to 9HA & M701J

Why Your Bypass System Needs a Gas Silencer

When the diverter damper sends exhaust straight to atmosphere in simple cycle, the stack mouth becomes a powerful noise source. Plants near communities, airports or site boundaries cannot run that way — the silencer is what makes simple-cycle switching legally and physically workable.

Without a silencer What it costs you With a Hangguo parallel plate silencer
High dynamic noise at the stack outlet during venting Complaints from communities and neighbouring facilities Sound energy absorbed inside the casing before it leaves the stack
Boundary or workplace noise limits exceeded Capped operating hours, penalties, or forced curtailment Helps the plant meet workplace and boundary noise regulations
Retrofit silencer later New steel, new foundations, and a scheduled outage Flange interface pre-detailed in the bypass design from day one
Generic catalogue silencer Back-pressure mismatch and re-work of the transition duct Sized against your flow, temperature and allowable pressure drop

How the Parallel Plate-form Silencer Works

When sound waves enter the silencer they set the air and fibres inside the porous material vibrating. Frictional and viscous resistance convert part of that sound energy into heat, which dissipates through the casing — the gas keeps moving, the noise does not.

The parallel plate arrangement keeps this absorption passive and durable: no moving parts, no consumables, and the flow path stays open, so back-pressure on the turbine stays predictable across the whole load range.

The result is a silencer with a simple structure, complete function, easy maintenance and long service life — suited to continuous outdoor duty in a power block.

Parallel plate-form gas silencer fabricated by Hangguo for bypass system

Parallel plate-form gas silencer.

  • The Parallel Plate-form Silencer
    The non-metallic expansion joint is designed between the diverter damper and the gas silence. The gas silence is supported on the bypass steel structure.
    read more
  • Exhaust Gas Silencer
    The gas silencer is the parallel plate-form silencer. The silencer is a device to obstruct the sound from spread and allows airflow to pass; it is the important mean to relieve the dynamic noise in
    read more

Construction: Three Sections, Two Material Systems

Section What it does Design note
Upper sound-deadening section Absorbs the first high-energy wave front entering from the duct side Plate spacing set by the gas flow area
Bottom sound-deadening section Traps the residual broadband noise before the flaring section Blade wrap: porous stainless steel sheet
Flaring section Recovers static pressure and guides flow into the stack at reduced velocity Angle sized against your allowable back-pressure
Material system Detail
Casing insulation Heat insulation layer of alumina silicate fiber keeps the casing surface safe to touch in hot exhaust duty
Sound-deadening blades Wrapped externally by porous stainless steel sheet — acoustically transparent and corrosion resistant in outdoor duty

Gas Silencer Engineering Summary

Typical values from delivered bypass systems. Final dimensions follow your flow, temperature and acoustic target — each silencer is calculated, not picked from a shelf. 【To be confirmed with client: values below reflect delivered project ranges, not catalogue limits】

Item Typical scope in our systems
Casing construction All-welded rectangular steel casing, externally stiffened, designed for the bypass steel structure load path
Casing insulation Alumina silicate fiber insulation layer over the full casing surface
Absorbing blades Parallel plates wrapped in porous stainless steel sheet, sized for gas temperature
Flaring section Built-in diffuser recovering static pressure before the stack transition
Flow area Sized to keep the exhaust velocity in the quiet band across the load range
Acoustic target Set by your boundary / community noise limit or plant specification
Back-pressure Traded openly against insertion loss — declared in our proposal, not hidden
Upstream interface Non-metallic expansion joint to the diverter damper, included in scope
Support Welded onto the bypass steel structure; loads in the same structural calculation
Drainage Drain points at the casing low points for condensate and wash water
Access Inspection openings for periodic blade condition checks
Turbine coverage 14+ gas turbine models, from 6B-class to 9HA and M701J

Integrated into the Bypass System, Not Bolted On

In our delivered systems the silencer sits mid-flue, and the interfaces are engineered together with the dampers and the steel structure:

Interface How we detail it
Upstream: diverter damper A non-metallic expansion joint is designed between the diverter damper and the gas silencer, absorbing thermal growth and vibration
Support: bypass steel structure The silencer is supported on the bypass steel structure — loads are accounted for in the same structural calculation
Downstream: stack Flanged transition into the bypass stack or exhaust stack, sized to keep flow velocity in the quiet band
Switching duty Positioned downstream of the damper so both the simple-cycle vent path and the HRSG route stay acoustically treated

This is the practical difference between a silencer vendor and a system supplier: alignment, growth, loads and noise are solved once, in one set of drawings, under one responsibility.

Gas Silencer Product Line

Parallel plate-form silencer for gas turbine bypass flue

The Parallel Plate-form Silencer

Our standard bypass silencer: upper and bottom sound-deadening sections plus flaring section, insulated casing, porous stainless steel wrapped blades, supported on the bypass steel structure.

View the parallel plate-form silencer →

Exhaust gas silencer for vent and intake noise elimination

Exhaust Gas Silencer

For general exhaust and intake noise elimination on vents and blow-off lines: an environmental protection equipment unit with simple structure and long service life, sized to your flow and noise target.

View the exhaust gas silencer →

Who Orders Gas Silencers From Us

Buyer Typical situation Their first question
EPC contractor New simple-cycle or switching power block under a fixed schedule Can the silencer arrive with the bypass package, tested as one system?
Plant owner / O&M Boundary noise complaints on an existing venting stack Can you retrofit without rebuilding our steel and foundations?
Gas turbine OEM / packager Exhaust package sub-contracted for a specific model Will you match our flange, load and pressure-drop interface?
Industrial plant Boiler or furnace blow-off lines venting to atmosphere What do you need from us to size it — and how fast?

Built and Tested in Our Own Works

Silencer casings are plate-rolled and welded in the same Hangzhou works as our dampers and stacks — one quality system, one inspection record. Welding production follows ISO 3834 / EN 3834 practice, and large casings are assembled, stiffened and insulated before painting in our 15 m × 12 m blasting and painting rooms.

Completed bypass packages — damper, silencer, steel structure and stack — are pre-assembled and function-tested in the works before shipment, then loaded at our own 1,000-tonne canal wharf for river-to-sea delivery. That is how a 126-system track record stays repeatable.

More about our factory and qualifications →

Gas silencer casing lifted by gantry crane at the Hangguo canal wharf for shipment

Silencer casing on the crane at our canal wharf.

Delivered Systems That Carried Our Silencers

Project Scope
Malaysia Samalaju, Sarawak Energy Complete turbine bypass system — diverter, silencer, steel structure and stack — tested in house before shipment
Iraq 10 × 9E conversion Bypass systems with silencers for the Shanghai Electric single-to-combined cycle program
Bahrain Alba 680 MW CCPP Bypass stack package with SEPCO III, TOC one month ahead of schedule, MEED 2025 award
Uzbekistan Syrdarya II Around 700 tonnes of bypass equipment delivered; first firing of GT2 confirmed on site

Behind the systems: ISO 9001 / 14001 / 45001, EN 1090 & EN 3834 welding production, EN 13084 steel chimney compliance, and draft-author status for China’s flue gas damper industry standard.

Bypass steel structure and flue erection at the Samalaju project site in Malaysia

Bypass structure erection, Samalaju site.

One Works, One Responsibility

Silencer and damper shipments loaded in protective frames at the Hangguo factory gate

Over-size casings leave the works in protective shipping frames, loaded at our own wharf.

Overseas customer delegation visiting the Hangzhou Boiler Group exhibition hall

Customer delegations visit our works and review silencer and bypass references before award.

Frequently Asked Questions

Why a parallel plate-form silencer instead of a reactive (chamber) type?

Parallel plate absorptive silencers handle the high flow, high temperature broadband noise of turbine exhaust with lower pressure drop and no tuning issues — the practical choice for bypass duty.

Will the silencer add back-pressure to my turbine?

Some, by design — that is why we size the flow area and flaring section against your allowable pressure drop rather than quoting a generic casing.

Can you guarantee a specific noise level at the stack outlet?

We size against your boundary or workplace noise target and state the design margin in the proposal; site verification depends on your layout, so we recommend agreeing the measurement method before award.

What temperature can the silencer casing and blades take?

The casing carries an alumina silicate fiber insulation layer, and the blades are wrapped in porous stainless steel sheet; exact limits follow your gas temperature in the sizing calculation.

How is the silencer supported?

On the bypass steel structure, with the loads included in the same structural calculation as the stack and dampers — no separate foundation design needed from your side.

Can it be retrofitted to an existing bypass system?

Yes, when the layout allows. Send us the existing GA drawings; the non-metallic expansion joint between damper and silencer absorbs the dimensional tolerances.

Is the expansion joint between the damper and silencer included?

Yes — the non-metallic expansion joint at that interface is part of our scope, detailed by the same team that designs the damper and the silencer.

What maintenance does it need?

Periodic visual inspection of the casing, drain points and blade sheets through the inspection openings. There are no moving parts or consumables.

Can you quote a silencer alone if I have my own stack?

Yes. We need gas flow, temperature, noise target and allowable pressure drop; we will match the flange interface to your existing stack.

How fast can you deliver?

Silencers ship as part of our bypass packages on the same project schedule; standalone units are quoted against the works loading plan. 【To be confirmed with client: standard lead time to state】

Request a Gas Silencer Quotation

Send your gas flow, temperature and noise target — our engineers reply with a sized silencer proposal and reference systems within one working day.

We're professional gas silencer manufacturers and suppliers in China for over 20 years, featured by good service and competitive price. We warmly welcome you to buy high quality gas silencer made in China here from our factory.

gas silencer for work boats, gas silencer for ceramic bikes, gas silencer for dishwasher systems
Send Inquiry